Toolstoday

Creating a self aligning glue joint using this Amana Tool 80 degree V Joint bit on the router table. The bit did a fantastic job cutting this making it a nearly seamless joint. This joint provides additional glue area strengthening the joint and is especially useful when making raised panels as the glue seam is much less noticeable when joined like this. All tools used are available from @toolstoday, be sure to check them out there. -- Amana Tool 80 degree V Joint bit, item no. 45790 JessEm Ultimate Excel II Router Table, item no. 09414 Woodpeckers in-DEXABLE Combo Square, item no. WP-CSQ-ST-20 JessEm Clear-Cut Stock Guides, item no. 04215 MicroJig GRR-Ripper push block, item no GR-100+

Cutting, prepping and trimming a dyed maple burl pen blank to turn for a gift. The carbide inserts on this Woodpeckers Ci Pen Mill kit cut this burl extremely cleanly trimming the wood back to the brass tube with absolutely no tear out! The tools used in this video are available on our website, be sure to check them out there! -- Woodpeckers Ultra-Shear Pen Mill Ci 13-piece set, item no. WP-PMCIDLX Wera Hex-Plus Metric L-Keys, item no. 05073593001 Rikon 1.75hp Bandsaw, item no. 10-326 Pica 3030 Pencil, item no. PC-3030/SB Starbond Thick CA Glue, item no. 20002 Starbond Accelerator, item no. A6

What do you think of how this Spektra™ logo turned out? Pouring the white and blue epoxy into the Spektra™ logo cut out with the Shaper Origin, item no. SO1-NN, all available on our website. ---- I then flattened off the majority of the epoxy using a router flattening jig and the Amana Tool. RC-2255 3 wing insert carbide flattening bit. I used TotalBoat High Performance 2:1 epoxy, also available on our website, and @mixolusa #25 White tint with some blue and white pigments for the X as well. I absolutely love the look of this!

Installing the AirWeights Universal Vacuum table, now available on our website, on our CNC machine. The 24"x48" complete setup shown here was very easy to install with the included pin locations file to ensure it is installed square to the machine! The table works great at holding super flexible material, like this plastic, that would be difficult to hold down any other way as well as other relatively flat non porous materials. Trying to pull it off the table maxed out my force gauge at 120lbs and it didn't budge. If your material has too much of a warp, cup or twist, vacuum tables will not be able to hold the material to the wasteboard, but holds great for most relatively flat materials. For smaller machines, we also offer AirWeights setups in 24"x24" tiles that you can combine to use on even larger areas if you wish! All tools used are available on our website, be sure to check them out there. -- AirWeights Complete 24"x48" vacuum workholding, item no. AWS-2448-SV1 Amana Tool 1/8" Spektra Downcut bit, item no. 46200-K i2R W.42 CNC machine, item no. i2RW42 Festool CXS 18 Drill, item no. FS-576887 Wera Kraftform XXL Screwdriver Set, item no. 05347106001

What do you think of how this project turned out? Making a leather tool pouch on the CNC machine using the Donek D4 Drag knife on the new Stepcraft Gen 3 D.840 CNC machine, all available on our website!  The drag knife cut the leather perfectly leaving nice clean cuts, I love watching it work! To drill the 5mm holes I used the 363005 solid carbide drill with the 365050 bushing and 47636 adapter at 50ipm plunge rate. For the 2mm holes I used the 363002 2mm solid carbide drill with the 364020 and 47636 adapters.

Cutting, installing and flush trimming some contrasting splines on the Thankful tray project. I love the contrasting splines, do you prefer contrasting splines or splines that match the wood color? The tools used in this video are available from @toolstoday, be sure to check them out on our website! --- SawStop 1.75hp PCS Table Saw, item no. PCS175-TGP252 Amana Tool 20T Flat Top Grind Blade, item no. RB1020C Plans for the Thankful Tray Project, item no. THANKFUL_TRAY Rikon 14" Deluxe Bandsaw 1.75hp, item no. 10-326 Amana Tool 3/4" 4 Flute Flush Trim Bit, item no. 57187 JessEm Ultimate Excel II Router Table, item no. 09414 Festool ETS 150/3 Sander, item no. FS-576079

What do you think of this workholding wasteboard? Making the workholding wasteboard on the Stepcraft M.1000 CNC machine. Be sure to check out the plans to make your own as well, item M_1000_BOARD, all available on the @toolstoday website!

What do you think of how this turned out? I could not be happier with how this project turned out! Making a wood perpetual calendar on the Stepcraft M.1000 CNC machine using the Amana Tool 45644-K 60 degree Spektra coated v-bit, 46202-K 1/4" downcut bit, 46200-K 1/8" downcut bit, 46315-K 1/4" Spektra™ coated upcut bit and plans for this project, item no. CALENDAR, all available from @toolstoday

Have you worked with HDPE before? I love v-carving @kingplastic Color Core on the Stepcraft M.1000 CNC machine using the Amana Tool #RC-45711 90° insert carbide v-groove bit both available from @toolstoday. After doing the carving I switched out for the Amana Tool 51404-K 1/4" spiral O flute Spektra coated upcut bit to cut the profile.

What do you think of how this shop utility cart project turned out? If you're interested in making this for yourself, plans for the project are available on our website, item no. SHOPCART. All tools used in this video are also available from @toolstoday, be sure to check them out on our website! -- Stepcraft M.1400 CNC machine, item no. stepcraft_M1400 Amana Tool 1/8" Carbide Drill bit, item no. SCFD-100 Amana Tool 90 Degree Insert Carbide V-Bit, item no. RC-45711 Amana Tool 1/4" compression bit, item no. 46170-K Black Box Storm Vacuum, item no. BBV-SVP-2 Festool CXS 18 Drill, item no. FS-576887 Festool CXS 12 Drill, item no. FS-576869 Amana Tool Adjustable No-Mar Carbide Tipped Countersink bit for Festool CENTROTEC System, item no. 55162 Amana Tool Adjustable No-Mar Carbide Tipped Countersink bit Hex Shank, item no. 55227